Optimisation of granola breakfast cereal manufacturing process by wet granulation and pneumatic conveying

dc.contributor.advisorByrne, Edmond P.
dc.contributor.authorPathare, Pankaj B.
dc.contributor.funderDepartment of Agriculture, Fisheries and Food, Irelanden
dc.date.accessioned2011-08-31T11:34:00Z
dc.date.available2011-08-31T11:34:00Z
dc.date.issued2010-07
dc.date.submitted2010-10-07
dc.description.abstractThis study has considered the optimisation of granola breakfast cereal manufacturing processes by wet granulation and pneumatic conveying. Granola is an aggregated food product used as a breakfast cereal and in cereal bars. Processing of granola involves mixing the dry ingredients (typically oats, nuts, etc.) followed by the addition of a binder which can contain honey, water and/or oil. In this work, the design and operation of two parallel wet granulation processes to produce aggregate granola products were incorporated: a) a high shear mixing granulation process followed by drying/toasting in an oven. b) a continuous fluidised bed followed by drying/toasting in an oven. In high shear granulation the influence of process parameters on key granule aggregate quality attributes such as granule size distribution and textural properties of granola were investigated. The experimental results show that the impeller rotational speed is the single most important process parameter which influences granola physical and textural properties. After that binder addition rate and wet massing time also show significant impacts on granule properties. Increasing the impeller speed and wet massing time increases the median granule size while also presenting a positive correlation with density. The combination of high impeller speed and low binder addition rate resulted in granules with the highest levels of hardness and crispness. In the fluidised bed granulation process the effect of nozzle air pressure and binder spray rate on key aggregate quality attributes were studied. The experimental results show that a decrease in nozzle air pressure leads to larger in mean granule size. The combination of lowest nozzle air pressure and lowest binder spray rate results in granules with the highest levels of hardness and crispness. Overall, the high shear granulation process led to larger, denser, less porous and stronger (less likely to break) aggregates than the fluidised bed process. The study also examined the particle breakage of granola during pneumatic conveying produced by both the high shear granulation and the fluidised bed granulation process. Products were pneumatically conveyed in a purpose built conveying rig designed to mimic product conveying and packaging. Three different conveying rig configurations were employed; a straight pipe, a rig consisting two 45° bends and one with 90° bend. Particle breakage increases with applied pressure drop, and a 90° bend pipe results in more attrition for all conveying velocities relative to other pipe geometry. Additionally for the granules produced in the high shear granulator; those produced at the highest impeller speed, while being the largest also have the lowest levels of proportional breakage while smaller granules produced at the lowest impeller speed have the highest levels of breakage. This effect clearly shows the importance of shear history (during granule production) on breakage during subsequent processing. In terms of the fluidised bed granulation, there was no single operating parameter that was deemed to have a significant effect on breakage during subsequent conveying. Finally, a simple power law breakage model based on process input parameters was developed for both manufacturing processes. It was found suitable for predicting the breakage of granola breakfast cereal at various applied air velocities using a number of pipe configurations, taking into account shear histories.en
dc.description.sponsorshipDepartment of Agriculture, Fisheries and Food, Ireland (FIRM)en
dc.description.statusNot peer revieweden
dc.description.versionAccepted Versionen
dc.format.mimetypeapplication/pdfen
dc.identifier.citationPathare, P.B., 2010. Optimisation of granola breakfast cereal manufacturing process by wet granulation and pneumatic conveying. PhD Thesis, University College Cork.en
dc.identifier.urihttps://hdl.handle.net/10468/397
dc.language.isoenen
dc.publisherUniversity College Corken
dc.relation.urihttp://library.ucc.ie/record=b2027070~S0
dc.rights© 2010, Pankaj B. Pathareen
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/3.0/en
dc.subjectGranola breakfast cerealen
dc.subjectHigh shear granulationen
dc.subjectFluidised bed granulationen
dc.subjectTexture propertiesen
dc.subjectPneumatic conveyingen
dc.subject.lcshCereal productsen
dc.subject.lcshGranulationen
dc.subject.lcshFood textureen
dc.subject.lcshFood processing machineryen
dc.subject.lcshPneumatic-tube transportationen
dc.titleOptimisation of granola breakfast cereal manufacturing process by wet granulation and pneumatic conveyingen
dc.typeDoctoral thesisen
dc.type.qualificationlevelDoctoralen
dc.type.qualificationnamePhD (Process & Chemical Engineering)en
Files
Original bundle
Now showing 1 - 1 of 1
Loading...
Thumbnail Image
Name:
PatharePB_PhD2010.pdf
Size:
10.84 MB
Format:
Adobe Portable Document Format
Description:
Full text available
License bundle
Now showing 1 - 2 of 2
Loading...
Thumbnail Image
Name:
license.txt
Size:
5.75 KB
Format:
Item-specific license agreed upon to submission
Description:
Loading...
Thumbnail Image
Name:
PankajPathareLicense.pdf
Size:
145.58 KB
Format:
Adobe Portable Document Format
Description:
License