High-efficiency photovoltaics through mechanically stacked integration of solar cells based on the InP lattice constant

Simple item page
dc.check.embargoformatNot applicableen
dc.check.infoNo embargo requireden
dc.check.opt-outNot applicableen
dc.check.reasonNo embargo requireden
dc.check.typeNo Embargo Required
dc.contributor.advisorCorbett, Brianen
dc.contributor.advisorMorrison, Alan P.en
dc.contributor.authorMathews, Ian P.
dc.contributor.funderEnterprise Irelanden
dc.contributor.funderEuropean Commissionen
dc.date.accessioned2014-11-10T12:06:43Z
dc.date.available2014-11-10T12:06:43Z
dc.date.issued2014
dc.date.submitted2014
dc.description.abstractSolar Energy is a clean and abundant energy source that can help reduce reliance on fossil fuels around which questions still persist about their contribution to climate and long-term availability. Monolithic triple-junction solar cells are currently the state of the art photovoltaic devices with champion cell efficiencies exceeding 40%, but their ultimate efficiency is restricted by the current-matching constraint of series-connected cells. The objective of this thesis was to investigate the use of solar cells with lattice constants equal to InP in order to reduce the constraint of current matching in multi-junction solar cells. This was addressed by two approaches: Firstly, the formation of mechanically stacked solar cells (MSSC) was investigated through the addition of separate connections to individual cells that make up a multi-junction device. An electrical and optical modelling approach identified separately connected InGaAs bottom cells stacked under dual-junction GaAs based top cells as a route to high efficiency. An InGaAs solar cell was fabricated on an InP substrate with a measured 1-Sun conversion efficiency of 9.3%. A comparative study of adhesives found benzocyclobutene to be the most suitable for bonding component cells in a mechanically stacked configuration owing to its higher thermal conductivity and refractive index when compared to other candidate adhesives. A flip-chip process was developed to bond single-junction GaAs and InGaAs cells with a measured 4-terminal MSSC efficiency of 25.2% under 1-Sun conditions. Additionally, a novel InAlAs solar cell was identified, which can be used to provide an alternative to the well established GaAs solar cell. As wide bandgap InAlAs solar cells have not been extensively investigated for use in photovoltaics, single-junction cells were fabricated and their properties relevant to PV operation analysed. Minority carrier diffusion lengths in the micrometre range were extracted, confirming InAlAs as a suitable material for use in III-V solar cells, and a 1-Sun conversion efficiency of 6.6% measured for cells with 800 nm thick absorber layers. Given the cost and small diameter of commercially available InP wafers, InGaAs and InAlAs solar cells were fabricated on alternative substrates, namely GaAs. As a first demonstration the lattice constant of a GaAs substrate was graded to InP using an InxGa1-xAs metamorphic buffer layer onto which cells were grown. This was the first demonstration of an InAlAs solar cell on an alternative substrate and an initial step towards fabricating these cells on Si. The results presented offer a route to developing multi-junction solar cell devices based on the InP lattice parameter, thus extending the range of available bandgaps for high efficiency cells.en
dc.description.sponsorshipEnterprise Ireland (TD/08/338 for the project MODCON-PV); European Commission (European regional development fund)en
dc.description.statusNot peer revieweden
dc.description.versionAccepted Version
dc.format.mimetypeapplication/pdfen
dc.identifier.citationMathews, I. P. 2014. High-efficiency photovoltaics through mechanically stacked integration of solar cells based on the InP lattice constant. PhD Thesis, University College Cork.en
dc.identifier.endpage163
dc.identifier.urihttps://hdl.handle.net/10468/1705
dc.language.isoenen
dc.publisherUniversity College Corken
dc.rights© 2014, Ian P. Mathewsen
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/3.0/en
dc.subjectSolar cellen
dc.subjectInPen
dc.subjectIndium phosphideen
dc.subjectMulti-junctionen
dc.subjectMechanical stacken
dc.subjectInGaAsen
dc.subjectInAlAsen
dc.subjectCPVen
dc.thesis.opt-outfalse
dc.titleHigh-efficiency photovoltaics through mechanically stacked integration of solar cells based on the InP lattice constanten
dc.typeDoctoral thesisen
dc.type.qualificationlevelDoctoralen
dc.type.qualificationnamePHD (Engineering)en
ucc.workflow.supervisora.morrison@ucc.ie
Files
Original bundle
Now showing 1 - 3 of 3
Thumbnail Image
Name:
MathewsIP_PhD2014.pdf
Size:
6.44 MB
Format:
Adobe Portable Document Format
Description:
Full Text E-thesis
Download
Thumbnail Image
Name:
Ian Mathews Thesis Abstract.pdf
Size:
6.55 KB
Format:
Adobe Portable Document Format
Description:
Abstract
Thumbnail Image
Name:
Re CORA Registration Notification.txt
Size:
5.67 KB
Format:
Plain Text
Description:
E-mail communication
License bundle
Now showing 1 - 1 of 1
Thumbnail Image
Name:
license.txt
Size:
5.62 KB
Format:
Item-specific license agreed upon to submission
Description:
Download
Collections
Doctoral Theses
Electrical and Electronic Engineering - Doctoral Theses
Tyndall National Institute - Doctoral Theses